Претраживање
Приказ резултата 1-10 од 19
Structural, Morphological and Electrical Properties of Alumina/YAG Composites as Solid Electrolyte for IT - SOFC
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2018)
Alumina/YAG composites (AYX_t) with high relative density (99.2 %TD) were successfully obtained by mixing commercial alumina powder with different volume fractions of yttrium aluminium garnet (Y3Al5O12-YAG; 7, 14, 21 and ...
An Experimental Study of Mechanical Properties and Heat Transfer of Acrylic Composites with Structural and Surface Modified Al2O3 Particles
(International Institute for the Science of Sintering (IISS), 2020)
Thermal properties of acrylate-based composite combined with alumina-based particles were investigated. The composites were made of poly (methyl methacrylate) (PMMA) modified with dimethyl itaconate (DMI) as a matrix. Neat ...
Structure and photocatalytic properties of sintered TiO2 nanotube arrays
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2018)
One-dimensional (1D) TiO2 nanotubes perpendicular to the substrate were obtained by electrochemical oxidation of titanium foil in an acid electrolyte. In order to alter the crystallinity and the morphology of films the ...
Thermal, Ceramic and Technological Properties of Clays used in Production of Roofing Tiles – Principal Component Analysis
(International Institute for the Science of Sintering, 2018)
This research describes a study of 11 selected samples of brick clays applied in roofing tile production, by using simultaneous thermal analysis. Additionally, the laboratory-sized samples were prepared and fired (850-950 ...
TiO2 nanotubes film/FTO glass interface: Thermal treatment effects
(ETRAN, 2022)
Pure Ti films deposited by radio-frequency magnetron sputtering on FTO glass were anodized to fabricate TiO2 nanotubes (NTs) arrays. The TiO2 NTs/FTO samples were sintered at 450, 550 and 630°C, in ambient air. The thermal ...
Impact of Alumina Particles on the Morphology and Mechanics of Hybrid Wood Plastic Composite Materials
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2019)
Hybrid composite panels of Wood-Plastic Composites (WPC) consisting of wood and poly (methyl methacrylate) (PMMA) were reinforced with alumina particles and made by "hot pressing" method. Alumina-based particles were made ...
Synthesis, Structure and Properties of Nickel-Iron-Tungsten Alloy Electrodeposits PART II: Effect of Microstructure on Hardness, Electrical and Magnetic Properties
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2016)
Nanostructured nickel-iron-tungsten alloys were produced by electrodeposition from an ammoniacal citrate bath. The tungsten content of the alloy ranged from 0.8 wt.% to 11 wt.%, and the crystal grain size of the FCC phase ...
Mechanical Properties of Biomass-derived Silica Nanoparticles Reinforced PMMA Composite Material
(Science of Sintering, 2022)
Rice husk was used to produce silica particles, which were then used to reinforce the polymer matrix. The synthesized SiO2 particles were characterized using X-ray diffraction, Fourier transforms infrared spectroscopy ...
Comparison of Mechanical Behavior of SiC Sintered Specimen to Analysis of Surface Defects
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2014)
Silicon carbide is the material that in sintered form is suiTab. for protection from impact as part of the multilayered structure. Its role is to accumulate energy from the projectile, to plastically deform the projectile ...
Solid state synthesis of extra phase-pure Li4Ti5O12 spinel
(Belgrade : International Institute for the Science of Sintering, 2011)
Extra phase-pure Li4Ti5O12 spinel with particle sizes less than 500 nm was synthesized by solid state reaction of mechanochemicaly activated mixture of nano anatase and Li2CO3 for a very short annealing time, 4 h at 800°C. ...