Претраживање
Приказ резултата 11-20 од 6759
A new technological solution for the manufacture of a borer for iron notch opening at the blast furnace plant / Primena aluminotermijskog postupka izrade i zavarivanja vrha burgija koje se koriste za otvoranje visoke peći tokom ispusta gvožđa
(Institut za istrazivanja i projektovanja u privredi, 2004)
A new technology for the manufacture of a borer by alumino-thermal method, system design for performing alumino-thermal reaction, as well as required quality of termite steel, is disclosed in this paper. In addition to ...
Electrooxidation of H-2, CO and H-2/CO mixtures on a well-characterized Pt-Re bulk alloy electrode and comparison with other Pt binary alloys
(Pergamon-Elsevier Science Ltd, Oxford, 1998)
We report new results for the electrooxidation of Hz, CO and H-2/CO mixtures on a Pt75Re25 bulk alloy using surface preparation in a UHV chamber and characterization by X-ray photoelectron spectroscopy (XPS). Sputter-cleaned ...
Investigation of the Microstructure and Distribution of Solute During Solidification of Al-Cu Alloy
(Springer Science and Business Media LLC, 1999)
Phenomenon of solidification process plays an important role in various areas like: crystal growth, casting processes, liquid phase sintering etc. Results presented in this paper contribute to investigation of the influence ...
Leaching kinetics of lead from lead (II) sulphate in aqueous calcium chloride and magnesium chloride solutions
(Elsevier Science Bv, Amsterdam, 1997)
The kinetics of lead leaching from lead (II) sulphate in aqueous calcium chloride and magnesium chloride solutions was studied. The leaching rates of lead were measured by using an agitated vessel at atmospheric pressure, ...
Correlation between apparent activation energy for hot working and temperature of no recrystallization in microalloyed steels
(Trans Tech Publications Ltd, Durnten-Zurich, 2003)
Two-stage linear ln[sinh(as)] vs 1/T plots, based on the stress data derived from either continuous or multipass flow curves generated by testing low carbon Nb/Ti microalloyed steel (Nb steel) and medium carbon V-microalloyed ...
Thermal shock of ceramic material : Comparison of resistance parameter with the critical ΔT values ΔTc = ΔTc(Bi) of ceramic materials
(Trans Tech Publications Ltd., 1997)
Thermal shock resistance of ceramic material can be characterized by using resistance parameters or critical temperature difference. Correlation between fracture resistance parameter, R and critical temperature difference, ...
On the aqueous oxidation of polymetallic Cu-Zn-Pb gold-bearing sulphide ore in an autoclave
(CIM Bulletin, 2001)
The paper presents a study on the oxidation of polymetallic gold ore by oxygen in an autoclave. It presents optimum parameters of autoclave leaching of sulphide refractory ore in self-generated sulphuric acid solutions ...
The acid resistance and corrosion stability of polyester coatings on phosphatized steel
(Serbian Chemical Society, Belgrade, 1998)
Protective polyester coatings on phosphatized steel were obtained with different combinations of diols (2-butyl-2-ethyl-1,3-propanediol or 2,2-dimethyl-1,3-propanediol), organic acids (1,3-cyclohexanedicarboxylic acid, ...
Selection of Calculation Method for Temperature Distribution in 99 Mass-% Al 2 O 3 Refractories
(Verlag Schmidt GmbH, 1998)
Refractories are constantly exposed to temperature changes. In most cases this exposure causes damage. In this work, attention is paid to problems of non-steady-state heat transfer. Some analytical and numerical methods ...
Thermodynamic modeling of vapor-liquid equilibria and excess properties of the binary systems containing diethers and n-alkanes by cubic equation of state
(Korean Institute Chemical Engineers, Seoul, 2004)
A comparison of the performances of two different approaches of cubic equations of state models, based on a classical van der Waals and mixing rules incorporating the G(E) equation, was carried out for correlation of ...